You’ve done a great job of Floor sanding Geelong. You’ve even vacuumed away all the dust and debris, but now you’re left with a dull and dirty look on the wood.
Don’t worry! There are still some easy things you can do to make your floor look like new again.
Preparing the floor
Before you start Floor sanding Geelong, you need to prepare the floor. The first step is cleaning the floor. Vacuum and mop it, then use a floor cleaner that removes grease and grime from your wood or laminate floors (don’t use harsh chemicals). This will make it much easier for you when you begin sanding later on.
Once the floor is dry, use a sanding block and 120-grit sandpaper to start smoothing out any rough spots. Move in the direction of the grain, either lengthwise or widthwise, depending on your floor type.
As you go along, check for places where your sanding blocks aren’t smoothing out all the bumps; these are usually caused by pieces of furniture or other items that have been left on the floor for a long time.
Sanding with a drum sander
There’s a special tool for sanding floors, and it’s called a drum sander. The drum sander is great because it allows you to sand your floor quickly while still getting the job done right.
Drum sanders are also much safer than traditional hand-powered sanders because they pull in air from outside of the room and force it through small holes in the drum itself, which helps keep dust from escaping into your home or office space.
However! Drum sanders cannot be used on certain types of floors: hardwood floors (because they will damage them), laminate floors (because they’re too soft) and low-quality plastic materials like linoleum or vinyl tiles (these will melt under high heat).
Vacuuming the dust away
Once you have removed the excess dust, vacuum the floor with a shop vac. You can use a brush attachment to get into corners and edges, and then clean up any remaining dust with a microfiber cloth.
If you’re using a vacuum with an air filter, it’s important to replace the filter after cleaning. This will prevent dust from getting back into your home and causing further problems for allergy sufferers.
Sanding the edges of your floor
Sanding the edges of your floor is a crucial step in achieving a beautiful finish.
- Sanding blocks are best for this job because they provide a flat edge and can be easily stored when not in use. They’re also less expensive than other tools, so if you’re on a budget, this is the way to go!
- Use a vacuum cleaner (with attachments) to remove dust from all surfaces before moving on to another area of sanding.
- A tack cloth will help remove any remaining bits of dust from the surface after vacuuming has been done–it’s like an extra layer of protection against little particles flying around while you work!
Final cleaning and vacuuming
Once your floor is dry, you’ll want to clean it. The first step is to vacuum the floor thoroughly with a soft brush attachment. If there are any stubborn spots or streaks left behind, wipe them away with a damp cloth and then follow up with a dry one.
Finally, give everything in the room (furniture, window treatments) a quick dusting so that it doesn’t get covered in sanding dust when you start walking on your newly finished floor!
Applying finish to your floor (polyurethane)
To apply the finish, you’ll need a brush or roller and some polyurethane. Polyurethane is a water-based finish that’s easy to apply and dries quickly. To make it even easier, we recommend using an applicator designed specifically for applying polyurethanes (like this one).
If you’re feeling adventurous, you can also try sanding your floor with fine-grit sandpaper before applying the polyurethane–this will give your floor a smooth surface and help prevent dust particles from getting stuck in between boards when they are being sanded down by hand.
You can see that there is a lot to do when preparing your Floor sanding Geelong. However, if you start early enough and follow these tips, it will be much easier for you to get the results you want.
If you don’t have much time or money available, then we recommend starting with just one room at a time before moving on to another area in your home. Make sure to select the right company after doing proper research and getting the right references. Timber floor sanding Melbourne specialises in timber floor polishing, sanding, staining, coating and repairs. We’ll see to it that you’re taken care of and receive all you require throughout the service.
